Eskimo 11608 User Manual download pdf

Check for parts online at www.geteskimo.com or call 800-345-6007 M-F 8-5 CST

Assembly Instructions

Universal Tow Hitch

(Fits sleds widths of 19, 21.5, 26.5, 28, & 32 inch)

ENGLISH

INSTRUCTIONS FOR THE FOLLOWING MODEL:

• Universal Tow Hitch (11608)

NOTE: Make sure there is enough room for the hitch to

pivot up or down without the hitch hitting the

lip of the sled. Attaching the hitch higher up will

cause the sled to tow “downward” and plow the

snow rather than ride on top of the snow.

2. Use the supports as a template to drill (4) 5/16” holes

through the sled, two holes on each side.

3. Attach the clamped supports to the sled using (4) 1/4-20

x 1-1/4” bolts, (4) 1/4” at washers, and (4) 1/4” nyloc nuts.

4. Attach assembled tow hitch to outer tub supports using

(2) 1/4-20 x 1-1/4” bolts and (2) 1/4-20 nyloc nuts.

WARNING

BEFORE EACH USE, READ, UNDERSTAND, AND

FOLLOW ALL ASSEMBLY, SAFETY, SETUP, AND USE

INSTRUCTIONS PROVIDED . FAILURE TO FOLLOW

ALL WARNINGS, CAUTIONS, AND INSTRUCTIONS

CAN RESULT IN INJURY OR DEATH.

• DO NOT MAKE SHARP TURNS.

• MAKE SURE TOW BAR IS SECURELY ATTACHED

BEFORE TOWING.

• DO NOT ALLOW CHILDREN OR PET TO RIDE IN

TUB WHEN TOWING.

• DO NOT USE ON UNEVEN TERRAIN OR SIDE OF

HILLS.

• DO NOT TOW UNDER THE INFLUENCE OF

DRUGS OR ALCOHOL.

• ALLOW EXTRA TIME AND DISTANCE WHEN

SLOWING DOWN OR STOPPING.

• DO NOT ATTACH HITCH TO AN UNAPPROVED

HITCH OR TOWING VEHICLE.

Assembly Instructions For Tow Hitch:

Tools Needed: Two 1/2” wrenches, C-clamp, and 5/16 drill bit.

IMPORTANT NOTE: Do not fully tighten any nut and

bolt combination until all bolt-on parts are assembled

together! Figer tighten only! This will allow alignment of

all parts during assembly.

1. To assemble tow hitch to the sled, attach the bolt

extension arms to the tow hitch receiver using (2) 1/4-20

x 1-13/4” bolt, (4) 1/4” at washers, and (2) 1/4-20 nyloc

nuts. SEE FIGURE 1.

NOTE: Make sure the hitch receiver is centered with the

front of the sled. Correct alignment will allow

the attaching bolts to insert into the correct hole

locations.

2. Attach the hitch tongue to the hitch receiver using (1) 1/4

x 1-3/4” snap pin.

Assemble Tow Hitch To Sled:

1. Use a C-clamp to hold the inner and outer tub supports

to the sides of the tub. The tub supports should be about

2-3/4” down from the lip of the tub. SEE FIGURE 2.

12122-0001R1

SLED TUB

1/4”-20 NYLOC NUT

1/4” FLAT WASHER

INNER TUB SUPPORT

OUTER TUB SUPPORT

1/4”-20 X 1-1/4 BOLT

1/4”-20 FLAT WASHER

1/4” FLAT WASHER

1/4”-20 X 1-1/4 BOLT

UNIVERSAL

TOW HITCH

FIGURE 2

12122-0002R1

1/4”-20 NYLOC NUT

1/4” FLAT WASHER

HITCH RECEIVER

EXTENSION ARM

1/4”-20 X 1-3/4 BOLT

1/4” FLAT WASHER

SNAP PIN

HITCH TONGUE

HITCH PIN

HAIR PIN

FIGURE 1

1 2 3 4

Summary of Contents

Page 1 - Universal Tow Hitch

Check for parts online at www.geteskimo.com or call 800-345-6007 M-F 8-5 CSTAssembly InstructionsUniversal Tow Hitch(Fits sleds widths of 19, 21.5, 26

Page 2 - ONEYEAR LIMITED WARRANTY

Assembly InstructionsUniversal Tow HitchEskimo®, Division of Ardisam, Inc. 800-345-6007 • Fax (715) 822-2223 E-mail: [email protected]/N: 12122-REV 3:

Page 3 - FRANÇAIS

Instructions d’assemblage de l’attelage:Outillage nécessaire - deux clés de 1/2po, serre-joint et foret de 5/16po. CONSEIL D’ASSEMBLAGE IMPORTANT

Page 4 - GARANTIE LIMITÉ UN AN

Comments to this Manuals

No comments

Eskimo 11608 User Manual

Browse online or download User Manual for Sports and recreation Eskimo 11608. Eskimo 11608 Manuel d'utilisation

Summary of Contents

Comments to this Manuals

Related products and manuals for Sports and recreation Eskimo 11608